Line Shaft



The Line Shaft Conveyor is a quiet and efficient live roller conveyor system. These systems are primarily suitable for lighter loads. Each roller is powered individually by spools, which in turn are connected fully by a composite “O” ring or band. Large, long systems can be run with a single drive shaft which includes: curves, pop-up transfers or spurs.


Application:
• Convey loads of Cartons, Totes, Fixtures, Cardboard Boxes
• Non-Contact Accumulation
• Zone Based
• Single load release when discharging products
• Moderate Incline/Decline/Curve/Transfers with same drive


Where it Works:
• Warehousing & Distribution
• Manufacturing
• Order Fulfillment
• Aerospace
• Government Military & Agency
• Automotive
• Parcel Handling




If you have any questions about line shafts, simply call us at (724) 969-1188 or use our online contact form.

Models of Line Shafts



LSLR19 – STRAIGHT LINE SHAFT BELT DRIVEN ROLLER WITH 1.90″ DIAMETER ROLLERS

LSLR19-LARGEModel LSLR19 is a minimum pressure line shaft belt driven live roller accumulation conveyor which can provide an economical means of accumulating products with minimal back pressure. This conveyor can be supplied with close roller centers, and is a reliable choice for package, carton or tote handling applications.

LSLR19 PDF Download

LSLR19 SPECIFICATIONS:

• BETWEEN FRAMES: 15″ – 39″
• BEGINNING ELEVATION: 12.25″- 126″
• ENDING ELEVATION: 12.25″ – 126″
• LENGTH: 24″ – 1200″
• SPEED: 20 – 180 FPM
• ROLLER CENTERS: 3″, 4.5″, 6″
• BELT: Standard belt is 83A, 15lb. capacity per roller. Optional high tension belt is 85A, 25 lb. capacity per roller. (Consult Factory for all high tension applications).
• DRIVE: Standard drive is center chain drive. (Timing belt required over 120FPM).
• MOTOR: 1/2 HP through 1-1/2 HP. Energy efficient and inverter duty motors also
available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 575/3/60 & DC
Voltage.
• ROLLER COVERS: Standard galvanized roller with precision ABEC bearings.
Optional polyurethane sleeves available.
• SUPPORT CENTERS: Standard supports are floor supports on 10’ centers.
Optional supports on 5’ centers. Ceiling supports are also available.
• FRAME SIZE: Drive frame 12″ x 1.50″ x 10 ga. Conveyor frame 7.50″ x 1.50″ x 10
ga. Both frames standard with bolt-In cross members, and welded end couplers.
• FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors
include green, beige, gray, orange, black and yellow.

LSTRC19 – CURVED LINE SHAFT BELT DRIVE ROLLER CONVEYOR WITH 2.50″ DIAMETER TAPERED ROLLERS

LSTRC19-LARGEModel LSTRC19 is a line shaft belt driven live roller curve that can provide positive drive for negotiating 90, 60, 45, and 30 degree turns. Used in light and medium duty applications, the tapered rollers help maintain product orientation through the curve.

LSTRC19 PDF Download

LSTRC19 SPECIFICATIONS:

• BETWEEN FRAMES: 15″- 27″ and >27″- 39″. (See chart on sht 2 for details).
• BEGINNING ELEVATION: 12.25″ – 126″
• ENDING ELEVATION: 12.25″ – 126″ SPEED: 20 – 180 FPM
• DEGREES: 30 , 45 , 60 , 90
• ROLLER CENTERS: Nominal 3″ on inside radius.
• BELT: Standard belt is 83A, 15 lb. capacity per roller. Optional high tension belt is 85A, 25 lb. capacity per roller. (Consult Factorty for high tension applications).
• DRIVE: Driven by LSLR19.
• ROLLER COVERS: Standard steel roller with precision ABEC bearings. Optional
polyurethane sleeves. Zinc plated rollers available.
• FRAME SIZE: 7.50″ x 1.50″ x 10 ga. Standard bolt-in cross members, and welded
end couplers.
• SUPPORT CENTERS: Standard (3) supports included per 90 curve, (2) supports
included per other angle options.
• FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors
include green, beige, gray, orange, black and yellow.

LSSP19 – STRAIGHT SPUR LINE SHAFT BELT DRIVEN ROLLER WITH 1.90″ DIAMETER ROLLERS

LSSP19-LARGEModel LSSP19 is a line shaft belt driven live roller conveyor used to divert off main trunk line conveyors at a 30 angle.

LSSP19 PDF Download

LSSP19 SPECIFICATIONS:

• BETWEEN FRAMES: 15″ – 39″
• BEGINNING ELEVATION: 12.25″ – 126″
• ENDING ELEVATION: 12.25″ – 126″
• LENGTH: See chart on sheet 2
• SPEED: 20 – 180 FPM
• ROLLER CENTERS: 3″
• BELT: Standard belt is 83A, 15 lb. capacity per roller. Optional high tension belt is
85A, 25 lb. capacity per roller. (Consult Factory for high tension applications).
• ROLLER COVERS: Standard galvanized roller covering with precision ABEC
bearings. Do Not use sleeves in main line of spur conveyor.
• DRIVE: Standard driven by LSLR19, from the conveyor beyond the spur. Optional
slave driven from the main conveyor (Option part number LSSPS19).
• SUPPORT CENTERS: Standard supports are floor supports on 10’ centers.
Optional supports on 5’ centers. Ceiling supports are also available.
• FRAME SIZE: 7.50″ x 1.50″ x 10 ga. Standard bolt-in cross members, and welded
end couplers.
• FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors
include green, beige, gray, orange, black and yellow.
• ORDER SEPERATELY: Diverter or Plow Arm with low friction face.

LSZP19 – ZERO PRESSURE LINE SHAFT BELT DRIVEN ROLLER WITH 1.90″ DIAMETER ROLLERS

LSZP19-LARGEModel LSZP19 is a medium duty line shaft belt driven zero pressure accumulation conveyor which can provide accumulation of light to medium weight loads with no back pressure. These units come equipped with zone control logic with easy set-up for cascade or slug release modes.

LSZP19 PDF Download

LSZP19 SPECIFICATIONS:

• BETWEEN FRAMES: 15″ – 39″
• BEGINNING ELEVATION: 12.25″ – 126″
• ENDING ELEVATION: 12.25″ – 126″
• LENGTH: 24″ – 1200″
• SPEED: 20 – 180 FPM
• ROLLER CENTERS: 3″, 4.5″, 6″, 9″, 12″
• BELT: Standard belt is 83A, 15 lb. capacity per roller. Optional high tension belt is 85A, 25 lb. capacity per roller. (Consult Factory for all high tension applications).
• DRIVE: Standard drive is center chain drive. (Timing belt required over 120FPM).
• MOTOR: 1/2 HP through1-1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 573/3/60 & DC Voltage.
• ROLLER COVERS: Standard galvanized roller coverings with precision ABEC bearings. Optional polyurethane sleeves available.
• SUPPORT CENTERS: Standard supports are floor supports on 10′ centers. Optional supports on 5′ centers. Ceiling supports are also available.
• FRAME SIZE: Drive frame 12″ x 1.50″ x 10 ga. Conveyor frame 7.50″ x 1.50″ x 10 ga. Both frames standard with bolt-In cross members, and welded end couplers.
• FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

LSHG19 – GAS SHOCK ASSISTED LINE SHAFT BELT DRIVEN ROLLER GATE WITH 1.90″ DIAMETER, 16 GAUGE ROLLERS

LSHG19-LARGEModel LSHG19 manually operated hinged gate provides convenient, economical passageway for personnel or equipment to either side of a conveyor line.

LSHG19 PDF Download

LSHG19 SPECIFICATIONS:

• BETWEEN FRAMES: 15″ – 39″
• BEGINNING ELEVATION: 18″ – 42″
• ENDING ELEVATION: 18″ – 42″
• GATE LENGTH: 36″or 48″
• SPEED: 20 – 180 FPM
• ROLLER CENTERS: 3″, 4.5″or 6″
• BELT: Standard belt is 83A, 15 lb. capacity per roller. Optional high tension belt is 85A, 25lb. capacity per roller. (Consult Factory for high tension applications).
• DRIVE: Driven by LSLR19.
• ROLLER COVERS: Standard galvanized roller covering with precision ABEC
bearings. Optional polyurethane sleeves available.
• FRAME SIZE: 7.50″ x 1.50″ x 10 ga. Standard bolt-on cross members.
• SUPPORT CENTERS: Standard supports are floor supports on 10’ centers.
Optional supports on 5’ centers. Ceiling supports are also available.
• FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors
include green, beige, gray, orange, black and yellow.

If you have any questions about the models of line shafts on this page, please call us at (724) 969-1188 or use our online contact form. We’ll help you identify the best solution that fits your project needs—as well as your budget.

–Jim & Ben Heinrich